Bora 1 Inch vs 1.5 Inch Wheel Spacers: Which Thickness Fits Your Truck?
When you’re deciding between wheel spacer thicknesses, the half-inch difference between 1 inch and 1.5 inch models changes more than just your track width. It affects tire clearance, your truck’s stance, steering feel, and whether your existing lug studs remain long enough for safe torque.
We manufacture both sizes at Bora, and we see the same questions every week: which thickness prevents rubbing without pushing wheels too far out, and which one actually fits the studs already installed on your hubs? This guide walks through the real-world differences so you can match spacer thickness to your truck’s suspension, tire size, and the look you’re after.

Track Width and Stance: What Half an Inch Actually Changes
A 1 inch spacer per side adds two inches to your total track width—one inch outboard on each wheel. A 1.5 inch spacer pushes that to three inches total.
The visual difference is obvious once both trucks are parked side by side. The 1 inch setup widens stance enough to fill the fender opening on most stock-height trucks, creating a more planted look without the wheels sitting outside the bodywork. The 1.5 inch thickness pushes the wheel face closer to—or slightly past—the fender lip, depending on your offset and tire width.
If you’ve already installed a leveling kit or mild lift, the 1.5 inch spacer usually delivers the aggressive stance most builders want. Stock-height trucks with narrow tires often find the 1 inch thickness gives them the visual improvement they’re after without requiring fender trimming or new mud flaps.
Tire Clearance: When Thickness Prevents Rubbing vs When It Creates New Contact Points
Inboard Clearance
The most common reason people buy wheel spacers in the first place is to stop tires from rubbing against upper control arms, coil buckets, or inner fender liners during full steering lock. Both 1 inch and 1.5 inch spacers move the tire outboard, creating more room between the tread and those inboard obstacles.
For light rubbing—contact only at full lock with a wheel turned hard left or right—a 1 inch spacer typically solves it. If you’re hearing scraping through most of the steering arc, or if you’ve installed wider wheels with more aggressive backspacing, the 1.5 inch thickness provides the extra clearance margin you need.
Outboard Clearance
Pushing wheels outboard also brings the outer sidewall closer to your fender. A 1.5 inch spacer on a truck with wide tires and limited wheel-well space can introduce new rubbing at the fender during compression—exactly the problem you were trying to avoid. Measure from your current tire sidewall to the inside of the fender lip before choosing thickness; if you have less than two inches of clearance at ride height, the 1.5 inch spacer will likely require trimming or aftermarket fender flares.
Stud Length and Hub Pilot Engagement: The Fit Constraint Most Guides Skip
Wheel spacer thickness isn’t just about stance—it’s limited by how much thread length your factory studs provide. Every wheel spacer slides over those studs, and your lug nuts still need at least six full threads of engagement for safe torque.
A 1 inch spacer consumes one inch of stud length. If your truck’s factory studs measure 2.5 inches from the hub face to the tip, you’re left with 1.5 inches of exposed thread for the wheel and lug nuts—plenty for most applications. A 1.5 inch spacer leaves only one inch of thread, which falls below the safe engagement minimum once the wheel is mounted.
When our 1.5 inch wheel spacers don’t leave enough thread, the fix is either extended lug studs pressed into your hubs or hub-centric spacers with their own pre-installed studs. The 1 inch thickness rarely requires stud replacement on trucks with OEM-length hardware, which is why it remains the more common choice for quick bolt-on installs.
If the spacer won’t slide over the hub pilot register at all—common when corrosion or casting tolerance stacks up—our guide on fixing spacers that won’t fit over the hub walks through the measurement and clearance steps that solve it.

Steering Feel and Suspension Geometry: How Thickness Affects Daily Driving
Moving your wheels outboard changes the leverage your tires apply to steering and suspension components. Both spacer thicknesses increase steering effort slightly—you’re effectively lengthening the moment arm between the tire contact patch and the ball joint—but the difference between 1 inch and 1.5 inch is perceptible if you drive the same truck before and after.
A 1 inch spacer produces a barely noticeable change in steering weight on most trucks. A 1.5 inch spacer makes the steering feel heavier at parking-lot speeds, and some drivers report a less direct, slightly vague on-center feel on the highway.
The thicker spacer also increases load on wheel bearings and ball joints because the tire’s outboard position creates more leverage during cornering and braking. For street-driven trucks with stock suspension, the added stress from a 1.5 inch spacer is well within component design limits, but it does mean bearings may require replacement a few thousand miles sooner than they would with thinner spacers or no spacers at all.

Material and Manufacturing: Why Thickness Alone Doesn’t Determine Strength
Both our 1 inch and 1.5 inch spacers are CNC-machined from billet aluminum, so the raw material strength is identical. The difference in thickness affects rigidity under side-load—thicker spacers deflect slightly less when cornering forces try to twist them—but both sizes exceed SAE and ISO load ratings for light-truck applications when properly torqued.
Hub-centric design matters more than thickness for preventing vibration. A spacer that fits loosely on the hub pilot or centers only on the lug studs will cause steering-wheel shake no matter how thick the aluminum is. Our spacers machine the pilot bore to within 0.002 inches of your truck’s hub diameter, keeping the assembly concentric whether you choose 1 inch or 1.5 inch.
Readers comparing hub-centric fitment across brands often ask about the differences in our tolerances versus competitors—our comparison of Bora and Supreme Suspensions covers how pilot-bore precision affects real-world vibration and bearing wear.
Matching Spacer Thickness to Your Build
The choice between 1 inch and 1.5 inch wheel spacers comes down to how much clearance you need, how much thread length your studs provide, and how aggressive a stance you want. The 1 inch thickness solves most light rubbing issues, works with factory studs on nearly every truck, and keeps steering feel close to stock. The 1.5 inch spacer delivers the wider, more planted look that pairs well with leveling kits and larger tires, but it often requires extended studs and occasionally needs fender trimming.
Measure your current tire-to-fender clearance, check your stud length, and decide whether you’re willing to modify components to accommodate the thicker spacer. Both sizes deliver the hub-centric fit and billet-aluminum strength that prevent vibration and hold up under daily driving—you’re choosing between two proven thicknesses, not a compromise.
Common Questions About 1 Inch and 1.5 Inch Wheel Spacer Fitment
Yes, staggered spacer thickness is common on trucks where the rear fenders have more clearance than the front or where you want a more aggressive rear stance. Just make sure each axle uses identical thickness side to side—running different thicknesses left to right creates asymmetric handling and uneven tire wear.
Wheel spacers themselves don’t void a factory warranty, but any component failure that a dealership can directly trace to spacer installation—such as a wheel bearing that failed due to increased side-load—may not be covered. The thicker 1.5 inch spacer increases bearing stress slightly more than the 1 inch, but both remain within design limits for most trucks when torqued correctly.
It depends on your current lug nuts and stud length. Most trucks with 1 inch spacers can reuse factory lug nuts if the studs are long enough. With 1.5 inch spacers, you’ll often need extended studs or spacers with built-in studs, and in that case you use the lug nuts specified for the spacer’s new stud length.
Our 1 inch aluminum spacers weigh approximately 2.5 pounds each; 1.5 inch spacers weigh around 3.5 pounds. Adding ten to fourteen pounds of unsprung weight per axle has a negligible effect on fuel economy—less than 0.1 mpg in real-world testing. The slight increase in track width and rolling resistance from wider stance affects mileage more than the spacer weight itself.
Stacking spacers is not recommended. Each spacer adds another set of mating surfaces and friction points, increasing the chance of loosening or misalignment. A single 1.5 inch spacer is always stronger, lighter, and safer than two thinner spacers stacked together.
If your wheels already sit closer to the fender than stock due to low offset, a 1 inch spacer is usually enough to clear inner obstacles without pushing the tire into the fender. A 1.5 inch spacer on top of aggressive offset often requires fender modification unless you’ve also installed a lift kit that opens up wheel-well space.